HUNTER GREEN METALLIC

Posted on July 16, 2013 by Adam Robertson
MC1041 HUNTER GREEN METALLIC
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 15 Minutes@ 375°F
MIN TEMP NA
MAX TEMP NA
RECOMMENDED THICKNESS 1.5 TO 3.5 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.26 +/- .05
THEORETICAL COVERAGE 56 sq/ft @ 2.0 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 85-95+
SALT SPRAY 1,000 hours
BALL IMPACT 80 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.
Comments Off on HUNTER GREEN METALLIC

SUBLIME TWIST

Posted on July 16, 2013 by Adam Robertson
MC1074 SUBLIME TWIST
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 375F/10 MIN
MIN TEMP 350F/15 MIN
MAX TEMP 400F/7 MIN
RECOMMENDED THICKNESS 2.0 TO 3.0 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.43 +/- .05
THEORETICAL COVERAGE 68 sq/ft @ 2.0 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 80-95+
SALT SPRAY n/a
BALL IMPACT 120 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.

 

 

Comments Off on SUBLIME TWIST

MAHOGANY METALLIC

Posted on July 16, 2013 by Adam Robertson
CHEMISTRY MAHOGANY METALLIC
CHEMISTRY POLYURETHANE Metallic
REGULAR CURE TEMP 15 Minutes@ 375°F
MIN TEMP NA
MAX TEMP NA
RECOMMENDED THICKNESS 1.5 TO 3.5 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.26 +/- .05
THEORETICAL COVERAGE 56 sq/ft @ 2.0 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 85-95+
SALT SPRAY 1,000 hours
BALL IMPACT 80 in/lb
SDS Sheet info # #8 – Polyurethane Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.

 

 

Comments Off on MAHOGANY METALLIC

BLUE ICE TEMPEST EXPLOSION

Posted on July 16, 2013 by Adam Robertson
MC1010 BLUE ICE TEMPEST EXPLOSION
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 15 Minutes@ 375°F
MIN TEMP NA
MAX TEMP NA
RECOMMENDED THICKNESS 1.5 TO 3.5 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.26 +/- .05
THEORETICAL COVERAGE 56 sq/ft @ 2.0 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 85-95+
SALT SPRAY 1,000 hours
BALL IMPACT 80 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.
Comments Off on BLUE ICE TEMPEST EXPLOSION

BLACK BRONZE ILLUSION

Posted on July 16, 2013 by Adam Robertson

BLACK BRONZE ILLUSION~ UNDER INDOOR LIGHT THE FINISH IS BLACK/BRONZE WITH A GOLD PEARL – PUT THE PRODUCT IN THE SUNLIGHT AND THE ILLUSION BEGINS !

 

MC1004 Black Bronze illusion
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 15 Minutes@ 375°F
MIN TEMP NA
MAX TEMP NA
RECOMMENDED THICKNESS 1.5 TO 3.5 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.26 +/- .05
THEORETICAL COVERAGE 56 sq/ft @ 2.0 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 85-95+
SALT SPRAY 1,000 hours
BALL IMPACT 80 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.
Comments Off on BLACK BRONZE ILLUSION

GRANET PEARL

Posted on July 16, 2013 by Adam Robertson
MC1033 GRANET PEARL
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 15 Minutes@ 375°F
MIN TEMP NA
MAX TEMP NA
RECOMMENDED THICKNESS 1.5 TO 3.5 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.26 +/- .05
THEORETICAL COVERAGE 56 sq/ft @ 2.0 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 85-95+
SALT SPRAY 1,000 hours
BALL IMPACT 80 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.
Comments Off on GRANET PEARL

SHATTERED BLUE

Posted on July 16, 2013 by Adam Robertson

SHATTERED BLUE POLYESTER POWDER    • GLOSS LEVEL = 80 -90% ON 60 DEGREE METER  • CURE SCHEDULE = 400F/10 MIN or 375/15min @ PMT  HARDNESS= H-2H IMPACT RESISTANCE: UP TO 80 IN/LB • RECOMMENDED MIL THICKNESS = 1.50 – 3.50 MILS  CROSS HATCH: 100%

*** CLEAR COAT NEEDED. EMERALD COATINGS RECOMMENDS A CLEAR FOR PROLONGED EXTERIOR USE AND IMPROVED MAR RESISTANCE.

Comments Off on SHATTERED BLUE

CHOCOLATE MAPLE METALLIC

Posted on July 16, 2013 by Adam Robertson
MC1020 CHOCOLATE MAPLE METALLIC
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 375F/10 MIN
MIN TEMP 350F/15 MIN
MAX TEMP 400F/7 MIN
RECOMMENDED THICKNESS 2.0 TO 3.0 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.42 +/- .05
THEORETICAL COVERAGE 68 sq/ft @ 2 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 80-95+
SALT SPRAY n/a
BALL IMPACT 120 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.

 

Comments Off on CHOCOLATE MAPLE METALLIC

PASSIONATE PINK

Posted on July 16, 2013 by Adam Robertson
CHEMISTRY PASSIONATE PINK
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 375F/10 MIN
MIN TEMP 350F/15 MIN
MAX TEMP 400F/7 MIN
RECOMMENDED THICKNESS 2.5-4 mils
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.41 +/- .05
THEORETICAL COVERAGE 55 sq/ft @ 2.5 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 80-95+
SALT SPRAY 1,000 hours
BALL IMPACT 120 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.
Comments Off on PASSIONATE PINK

FLAME RED COPPER BLAST

Posted on July 16, 2013 by Adam Robertson
MC1030 FLAME RED COPPER BLAST
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 400F/10 MIN @ PART METAL TEMPERATURE
MIN TEMP NA
MAX TEMP NA
RECOMMENDED THICKNESS 2.5-3.5 mils
PENCIL HARDNESS 2H minimum
SPECIFIC GRAVITY 1.2-1.8 g/cm3
THEORETICAL COVERAGE 51.5 ft2 /lb at 2.5 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 80-95+
SALT SPRAY 1,000 hours
BALL IMPACT 80 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.
Comments Off on FLAME RED COPPER BLAST

TOXIC WASTE GREEN

Posted on July 16, 2013 by Adam Robertson
MC1078 TOXIC WASTE GREEN
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 375F/10 MIN
MIN TEMP 350F/15 MIN
MAX TEMP 400F/7 MIN
RECOMMENDED THICKNESS 2.5 TO 4 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.38 +/- .05
THEORETICAL COVERAGE 56 sq/ft @ 2.5 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 80-95+
SALT SPRAY 1,000 hours
BALL IMPACT 120 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.

 

 

 

Comments Off on TOXIC WASTE GREEN

TOXIC MANGO PEARL

Posted on July 16, 2013 by Adam Robertson
MC1077 TOXIC MANGO PEARL
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 375F/10 MIN
MIN TEMP 350F/15 MIN
MAX TEMP 400F/7 MIN
RECOMMENDED THICKNESS 2.5 TO 3.5 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.42 +/- .05
THEORETICAL COVERAGE 54 sq/ft @ 2.5 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 80-95+
SALT SPRAY 1,000 hours
BALL IMPACT 120 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.

 

Comments Off on TOXIC MANGO PEARL

GREEN GHOST PEARL

Posted on July 16, 2013 by Adam Robertson

 

MC1034 GREEN GHOST PEARL
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 375F/10 MIN
MIN TEMP 350F/15 MIN
MAX TEMP 400F/7 MIN
RECOMMENDED THICKNESS 2.5 TO 4 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.38 +/- .05
THEORETICAL COVERAGE 56 sq/ft @ 2.5 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 80-95+
SALT SPRAY 1,000 hours
BALL IMPACT 120 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.
Comments Off on GREEN GHOST PEARL

BRIGHT GREEN PEARL

Posted on July 16, 2013 by Adam Robertson
MC1013 BRIGHT GREEN PEARL
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 375F/10 MIN
MIN TEMP 350F/15 MIN
MAX TEMP 400F/7 MIN
RECOMMENDED THICKNESS 2.5 TO 4 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.38 +/- .05
THEORETICAL COVERAGE 56 sq/ft @ 2.5 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 80-95+
SALT SPRAY 1,000 hours
BALL IMPACT 120 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.
Comments Off on BRIGHT GREEN PEARL

BRIGHT YELLOW PEARL

Posted on July 16, 2013 by Adam Robertson

BRIGHT YELLOW PEARL

MC1015 BRIGHT YELLOW PEARL
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 375F/10 MIN
MIN TEMP 350F/15 MIN
MAX TEMP 400F/7 MIN
RECOMMENDED THICKNESS 2.5 TO 3.5 MILS
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.38 +/- .05
THEORETICAL COVERAGE 56 sq/ft @ 2.5 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 80-95+
SALT SPRAY 1,000 hours
BALL IMPACT 120 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.

 

 

Comments Off on BRIGHT YELLOW PEARL

BUTANE SODA POP

Posted on July 16, 2013 by Adam Robertson

BUTANE SODA POP, A bright pink with a light blue pearl through the finish.

MC1017 BUTANE SODA POP
CHEMISTRY Polyester TGIC Metallic
REGULAR CURE TEMP 375F/10 MIN
MIN TEMP 350F/15 MIN
MAX TEMP 400F/7 MIN
RECOMMENDED THICKNESS 2.5-4 mils
PENCIL HARDNESS 2H
SPECIFIC GRAVITY 1.41 +/- .05
THEORETICAL COVERAGE 55 sq/ft @ 2.5 mils
PENCIL HARDNESS 2H minimum
GLOSS LEVEL (60°) 80-95+
SALT SPRAY 1,000 hours
BALL IMPACT 120 in/lb
SDS Sheet info # #9 – Polyester TGIC Metallic
SDS link https://emeraldcoatings.com/sds-sheets/
*Clear Coat Recommended, will Improved Mar Resistance and will improve the over all look and depth of the metallic finish.  *When coating in 2-3 stages, always particularly cure the base coat around 50-75% of the recommended cure schedule to allow the top coat to properly cross-link with the base coat. This method of curing will result in the best possible bond between coats. Over curing the base coat can cause possible delamination between coatings.
Comments Off on BUTANE SODA POP